3S-FRM-150 Non-Penetrating Roof Mount -w- 58" x 1.50" Mast
Made in the USA!
Ideal for Light Off-Air TV and Wireless Internet Antenna mounting, is constructed of pre-galvanized 12 ga. steel, uses 6 standard concrete blocks to anchor, 35" x 35" base. Mast pipe length will be 58" actual length for shipping purposes.
For light antenna loads needing 10 feet in total height,
the Optional 1.50" x 58" Swaged Pipe extension kit includes:
(1) 3S 5-50S Swaged Pipe
(1) 3S 60A-50' Steel Guy Wire
(1) 3S 43-A Guy Ring
(8) 1/8" CCF Guy Clamps
Height and Antenna Loading capability are dependent upon ballast weight... You need to Consult an Engineer to determine the Load Bearing Capability of the roof that you are entertaining such an Installation. It is Important to choose a Mount and Mounting Location with a Picture of the Finished Installation in Mind. Be Sure to First select a location that lends itself to applying a Load without Compromising the Integrity of the Material you affix to. Most Decorative Finishes most often do not have the Strength to Hold a Weight or Pressure without fail. Further, Think about what's underneath the exterior. Is it stronger, or will it yield to Pressure over time also? Weather Proof the Installation to Maintain the Integrity of your Home. Next consider the Location over a Lifetime of Adjustments, does it lend itself to modifications in Height or Direction? Larger Antennas increase the surface area presented to air movement, Hence, Wind-load does increase. As the length of the mast increases from Its last attached point on the structure, the torque applied in cantilever also increases with Weight and Wind-Load, requiring a more substantive attachment and Load-Bearing material. Keep the Distance Minimal from the Antenna to the TV's and Equipment you feed, as to minimize loss and the need for Amplification.
3 Star FRMPAD Protective Barrier Pad for FRM Mounts
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/8 thick Pad measures roughly 18 wide by 42 inches long, includes 2 each per set, place underneath Frame of Non-Penetrating mount, on top of Roof surface...
3 Star 3S-150S 1.50 O.D. Steel Satellite Dish Swaged Ground Pole Mast
Ideal as a DISH500 and DIRECTV Dish Antenna Mast (will NOT work for DIRECTVs SL3/5) for Ground or Wall mount Installation (Mount Not Included)...
3 Star CW12S #12 Solid Copper Ground Wire
25 feet of #12 Solid Copper wire as used for common grounding applications involving Low-Voltage Communications installations like Cable TV, TV Antenna, Satellite TV and Wireless Internet. Priced and sold by the foot in continuous roll (25 ft. per unit ordered)...
GR-4 - 5/8" x 4' Bonded Ground Rod
Uniform Electrolytic Copper On Steel Core, Minimum Copper Depth 10 Mils, UL Listed. Use 5/8 inch Ground Rod Clamp for #6, #4 copper, use 3/4 inch clamp with steel wire rope (sold separately). Suitable for burial after attachment (see our self amalgamating tape sealant). Use for Grounding of Tower Base and Down Guys or Telescopic Antenna Masts. Select a ground rod clamp based on conductor to be attached (see details)...
3 Star GC-2 Tower Base Section Ground Clamp
Pipe Clamp (1.25 to 2.00 Inch OD) used for Ground Connection to 55G and 65G Fixed Rigid Base and Main Tower Sections. Can also used on Telescopic masts and 25G 45G...
1. 3S-FRM-150 Non-Penetrating Roof Mount - With 58" x 1.50" Mast - $110.00 | 2. HOLLAND 20 dB Directional Coupler 5-1000 MHz. - $2.45 |
3. 42" - 70" FLAT PANEL FLUSH MOUNT - BLACK - FP-LFB - $80.00 | 4. FAM-6HR 6 dB In Line Attenuator Pad - $2.75 |
New Store to Open 2024
Three Star Inc.
5750 Stuart Ave.
Jacksonville, FL 32254
Your Orders are Currently being Processed and Shipped out of Richmond, VA.