ROHN GAC5955TOP Concrete Guy Anchor Rod with 5 Hole Equalizer Plate
Anchor Rod with Integral Equalizer Plate for 3 or 5 level Down Guy Attachment via use of Eye to Jaw Turnbuckles, embeds in Concrete Anchor Block for Guying Down ROHN Towers with 64,800 lbs. allowable load...

 ROHN Universal One Legged Mount

Made in the USA!
One-Legged Gable Mount is designed for virtually all types of antennas – home, TV, MMDS, DBS and more...

Rohn GEM-44060 Galvanized Eave Mount Antenna Mast Bracket

Used for easy mounting on the eave of a house. Lower Bracket of 16 gauge Hot Dip Galvanized steel, non-adjustable 48 inches. Both the upper and lower brackets are for masts up to 2.25 inches in diameter with clamps, bolts and 2.5 inch lag screws. Mast can pass by lower Bracket for Ground mount installations (Mast Not Included). Will stand-off mast 2.25 inches from surface...

PNTNPO5 Tower Paint - Orange
Rohn orange, water based tower paint for use on untreated galvanized surfaces Covers 200-400 square feet per gal. at 1-2 mils thickness.

PNTNPW9 Tower Paint - White
Rohn white, water based tower paint for use on untreated galvanized surfaces Covers 200-400 square feet per gal. at 1-2 mils thickness.

ROHN FRM-MAT Satellite Dish Non-penetrating Roof Mount Rubber Protective Mat
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/32 thick Pad measures roughly 36 wide by 42 inches long, trims neatly, place underneath Frame of Non-Penetrating mount, on top of Roof surface...

ROHN JRMMAT Protective Rubber Mat for JRM Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 1/8 thick Mat is for placement underneath the Frame of a JRM Non-Penetrating mount, on top of Roof surface...

ROHN JRMPAD Protective Barrier Pad for JRM Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/8 thick Pad is for placement underneath the Frame of a JRM Non-Penetrating mount, on top of Roof surface...

ROHN BRM4MAT Protective Rubber Mat for BRM4 Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 1/8 thick Mat is for placement underneath the Frame of a BRM4 Non-Penetrating mount, on top of Roof surface...

ROHN BRM4PAD Protective Barrier Pad for BRM4 Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/8 thick Pad is for placement underneath the Frame of a BRM4 Non-Penetrating mount, on top of Roof surface...

ROHN BRM6MAT Protective Rubber Mat for BRM6 Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 1/8 thick Mat is for placement underneath the Frame of a BRM6 Non-Penetrating mount, on top of Roof surface...

ROHN BRM6PAD Protective Barrier Pad for BRM6/ 25GBRM Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/8 thick Pad is for placement underneath the Frame of a BRM6 Non-Penetrating mount, on top of Roof surface...

 ROHN Universal One Legged Mount

Made in the USA!
One-Legged Gable Mount is designed for virtually all types of antennas – home, TV, MMDS, DBS and more...

ROHN NPPK Non-Penetrating Dish Antenna Roof Peak Mount
Made in the USA!
This new non-penetrating peak roof mount is a great solution for broadband antennas and satellite TV dishes. The adjustable mounting plate can be center mounted or to one side as needed to accommodate your satellite TV dish mounts (not included). The 1LG mount with a base and 1-1/4” mounting tube is an option for the NPPK.

ROHN FRM125 Non-Penetrating Roof Mount 1.25 x 60 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 3’ square with a 16” tray to fit concrete blocks, typically used as ballast. The base mount and mast tube are 16 gauge Pre-Galvanized for corrosion protection.

ROHN FRM150 Non-Penetrating Roof Mount 1.50 x 30 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 3’ square with a 16” tray to fit concrete blocks, typically used as ballast. The base mount and mast tube are 16 gauge Pre-Galvanized for corrosion protection.

ROHN FRM166 Non-Penetrating Roof Mount 1.66 x 30 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 3’ square with a 16” tray to fit concrete blocks, typically used as ballast. The base mount and mast tube are 16 gauge Pre-Galvanized for corrosion protection.

ROHN FRM225 Non-Penetrating Roof Mount 2.25 x 60 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 3’ square with a 16” tray to fit concrete blocks, typically used as ballast. The base mount is 16 gauge Pre-Galvanized and the mast tube is thick-walled galvanized steel for corrosion protection.

ROHN FRM238 Non-Penetrating Roof Mount 2.375 x 30 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 3’ square with a 16” tray to fit concrete blocks, typically used as ballast. The base mount is 16 gauge Pre-Galvanized and the mast tube is thick-walled galvanized steel for corrosion protection.

ROHN FRM238SP5 Non-Penetrating Roof Mount 2.375 x 60 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 3’ square with a 16” tray to fit concrete blocks, typically used as ballast. The base mount is 16 gauge Pre-Galvanized and the mast tube is thick-walled galvanized steel for corrosion protection.

ROHN JRM23805 Non Pentrating Ballast Roof Mount 2.375 in. x 5 ft. Mast
Made in the USA!
Mast Dimensions - 2“ STD. Pipe (2-3/8 O.D.) x 60”
The JRM is a non-penetrating, 5' square ballast type roof mount that supports a 5’ pipe mast with up to 12 standard concrete blocks as ballast. The JRM is used in cellular, PCS, broadband and other applications.
This Item Ships LTL Freight ONLY...

ROHN JRM23855 Non Pentrating Ballast Roof Mount 2.375 in. x 10 ft. Mast
Made in the USA!
Mast Dimensions - 2“ STD. Pipe (2-3/8 O.D.) x 120” ( 2 Piece Mast 2 3/8 x 60" )
The JRM is a non-penetrating, 5' square ballast type roof mount that extends to a 10’ pipe mast with up to 12 standard concrete blocks as ballast. The JRM is used in cellular, PCS, broadband and other applications.
This Item Ships LTL Freight ONLY...

ROHN JRM23810 Non Pentrating Ballast Roof Mount 2.375 in. x 10 ft. Mast
Made in the USA!
Mast Dimensions - 2“ STD. Pipe (2-3/8 O.D.) x 120”
The JRM is a non-penetrating, 5' square ballast type roof mount supporting a 10’ pipe mast with up to 12 standard concrete blocks as ballast. The JRM is used in cellular, PCS, broadband and other applications.
This Item Ships LTL Freight ONLY...

ROHN JRM27505 Non Pentrating Ballast Roof Mount 2.875 in. x 5 ft. Mast
Made in the USA!
Mast Dimensions - 2.5“ STD. Pipe (2-7/8 O.D.) x 60”
The JRM is a non-penetrating, 5' square ballast type roof mount that supports a 5’ pipe mast with up to 12 standard concrete blocks as ballast. The JRM is used in cellular, PCS, broadband and other applications.
This Item Ships LTL Freight ONLY...

ROHN JRM27555 Non Pentrating Ballast Roof Mount 2.875 in. x 10 ft. Mast ( 2 Piece )

Made in the USA!
 Mast Dimensions - 2.5“ STD. Pipe (2-7/8 O.D.) x 120” ( 2 Piece Mast 2 7/8 x 60"
The JRM is a non-penetrating, 5' square ballast type roof mount supporting a 10’ pipe mast with up to 12 standard concrete blocks as ballast. The JRM is used in cellular, PCS, broadband and other applications.
This Item Ships LTL Freight ONLY...

ROHN JRM27510 Non Pentrating Ballast Roof Mount 2.875 in. x 10 ft. Mast
Made in the USA!
Mast Dimensions - 2.5“ STD. Pipe (2-7/8 O.D.) x 120”
The JRM is a non-penetrating, 5' square ballast type roof mount supporting a 10’ pipe mast with up to 12 standard concrete blocks as ballast. The JRM is used in cellular, PCS, broadband and other applications.
This Item Ships LTL Freight ONLY...

ROHN JRM35010 Non Pentrating Ballast Roof Mount 3.5in.O.D. x 10 ft. Mast
Made in the USA!
Mast Dimensions - 3“ STD. Pipe (3-1/2 O.D.) x 120”
The JRM is a non-penetrating, 5' square ballast type roof mount supporting a 10’ pipe mast with up to 12 standard concrete blocks as ballast. The JRM is used in cellular, PCS, broadband and other applications.
This Item Ships LTL Freight ONLY...

ROHN BRM425 Non-Penetrating Roof Mount 2.50 inch x 3 foot Mast
Made in the USA!
Mast Dimensions - 2” STD. Pipe (2-3/8 O.D.) x 34 1/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 6' - 6" square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM42510 Non-Penetrating Roof Mount 2.38 inch x 10 foot Mast
Made in the USA!
Mast Dimensions - 2” STD. Pipe (2.38O.D.) x 10'
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 6' - 6" square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM430 Non-Penetrating Roof Mount 3.00 inch x 3 foot Mast
Made in the USA!
Mast Dimensions - 2-1/2” STD. Pipe (2-7/8 O.D.) x 34-1/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 6' - 6" square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM435 Non-Penetrating Roof Mount 3.50 inch x 3 foot Mast
Made in the USA!
Mast Dimensions - 3” STD. Pipe (3-1/2 O.D.) x 34-1/4"
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 6' - 6" square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM440 Non-Penetrating Roof Mount 4.00 inch x 3 foot Mast
Made in the USA!
Mast Dimensions - 3-1/2” STD. Pipe (4 O.D.) x 34-1/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 6' - 6" square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM445 Non-Penetrating Roof Mount 4.50 inch x 3 foot Mast
Made in the USA!
Mast Dimensions - 4” STD. Pipe (4-1/2 O.D.) x 34-1/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 6' - 6" square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM44510 Non-Penetrating Roof Mount 4.50 inch x 10 foot Mast
Made in the USA!
Mast Dimensions - 4” STD. Pipe (4-1/2 O.D.) x 10'
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 6' - 6" square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM630M Non-Penetrating Roof Mount 3.00 inch x 4 foot Mast
Made in the USA!
Mast Dimensions - 2.5” STD. Pipe (2-7/8 O.D.) x 45-3/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 10' square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM635M Non-Penetrating Roof Mount 3.50 inch x 4 foot Mast
Made in the USA!
Mast Dimensions - 3” STD. Pipe (3-1/2 O.D.) x 45-3/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 10' square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM640M Non-Penetrating Roof Mount 4.00 inch x 4 foot Mast
Made in the USA!
Mast Dimensions - 3.5” STD. Pipe (4 O.D.) x 45-3/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 10' square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM645M Non-Penetrating Roof Mount 4.50 inch x 4 foot Mast
Made in the USA!
Mast Dimensions - 4” STD. Pipe (4-1/2O.D.) x 45-3/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 10' square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM64510M Non-Penetrating Roof Mount 4.50 inch x 10 foot Mast
Made in the USA!
Mast Dimensions - 4” STD. Pipe (4-1/2O.D.) x 117-3/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 10' square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM655M Non-Penetrating Roof Mount 5.50 inch x 4 foot Mast
Made in the USA!
Mast Dimensions - 5” STD. Pipe (5-9/16 O.D.) x 45-3/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 10' square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN BRM665M Non-Penetrating Roof Mount 6.50 inch x 4 foot Mast
Made in the USA!
Mast Dimensions - 6“ STD. Pipe (6-5/8 O.D.) x 45 -3/4”
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 10' square with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN AAGM35 Non-Penetrating Roof Mount 3.50 x 54 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 191" by 166" hexoganal with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN AAGM40 Non-Penetrating Roof Mount 4.00 x 54 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 191" by 166" hexoganal with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN AAGM45 Non-Penetrating Roof Mount 4.50 x 54 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 191" by 166" hexoganal with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN AAGM55 Non-Penetrating Roof Mount 5.50 x 54 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 191" by 166" hexoganal with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN AAGM65 Non-Penetrating Roof Mount 6-5/8 x 54 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 191" by 166" hexoganal with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN AAGM65 Non-Penetrating Roof Mount 6-5/8 x 60 inch Mast
Made in the USA!
This roof mount is able to support various Antenna EPA's depending on wind and Ballast load (see details). The base of the roof mount is 191" by 166" hexoganal with a 16” tray to fit concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN PRM635 Non-Penetrating Roof Mount 3.50 x 50 inch Mast
Made in the USA!
Mast Dimensions - 3“ STD. Pipe (3-1/2 O.D.) x 50-5/16”
This non penetrating roof mount is capable of supporting dishes up to 6' in diameter for PCS, wireless, cable, DBS satellite and UHF/VHF reception depending on wind and Ballast load (see details). The base of the roof mount is 10.5’ triangular using 48 standard concrete blocks used as ballast to form the base.

ROHN PRM640 Non-Penetrating Roof Mount 4.00 x 50 inch Mast
Made in the USA!
Mast Dimensions - 3.5“ STD. Pipe (4 O.D.) x 50-5/16”
This non penetrating roof mount is capable of supporting dishes up to 6' in diameter for PCS, wireless, cable, DBS satellite and UHF/VHF reception depending on wind and Ballast load (see details). The base of the roof mount is 10.5’ triangular using 48 standard concrete blocks used as ballast to form the base.

ROHN PRM645 Non-Penetrating Roof Mount 4.50 x 50 inch Mast
Made in the USA!
Mast Dimensions - 4“ STD. Pipe (4-1/2 O.D.) x 50-5/16”
This non penetrating roof mount is capable of supporting dishes up to 6' in diameter for PCS, wireless, cable, DBS satellite and UHF/VHF reception depending on wind and Ballast load (see details). The base of the roof mount is 10.5’ triangular using 48 standard concrete blocks used as ballast to form the base.

ROHN PRM655 Non-Penetrating Roof Mount 5.50 x 50 inch Mast
Made in the USA!
Mast Dimensions - 5“ STD. Pipe (5-9/16 O.D.) x 50-5/16”
This non penetrating roof mount is capable of supporting dishes up to 6' in diameter for PCS, wireless, cable, DBS satellite and UHF/VHF reception depending on wind and Ballast load (see details). The base of the roof mount is 10.5’ triangular using 48 standard concrete blocks used as ballast to form the base.

ROHN 25GBRM BRM6X Ballast Roof Mount for 25G
The 25GBRM non-penetrating roof mount, is designed to support 25G tower sections. The roof mount is able to support 2 sections of 25G tower in self supporting tower applications. The base of the roof mount is 10’ square with a 16” tray to fit the concrete blocks, typically used as ballast.
This Item Ships LTL Freight ONLY...

ROHN URM Universal Antenna Roof Mount
Made in the USA!
Capable of supporting most TVRO, PCS, Cellular, and Microwave antennas. The Universal Roof Mount adapts to various roof pitches and the fully adjustable rear-leg allows for use on a flat or up to a 12”/12” pitched roof. Installation is easy because of the quick adaptability, plus there’s no need for concrete block. Optional Mounting Pipe for Antennas sold separately (see Details)...

ROHN SHRM Saw Horse Dish Antenna Roof Mount
Made in the USA!
Capable of supporting most TVRO, PCS, Cellular, and Microwave antennas (not included). The Saw Horse Roof Mount allows for placement of antennas on the roof peak with up to a 12”/12” pitched roof. Can also be placed on flat roof. Optional Mounting Pipe for Antennas sold separately (see Details)...

ROHN FRM-MAT Satellite Dish Non-penetrating Roof Mount Rubber Protective Mat
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/32 thick Pad measures roughly 36 wide by 42 inches long, trims neatly, place underneath Frame of Non-Penetrating mount, on top of Roof surface...

ROHN JRMMAT Protective Rubber Mat for JRM Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 1/8 thick Mat is for placement underneath the Frame of a JRM Non-Penetrating mount, on top of Roof surface...

ROHN JRMPAD Protective Barrier Pad for JRM Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/8 thick Pad is for placement underneath the Frame of a JRM Non-Penetrating mount, on top of Roof surface...

ROHN BRM4MAT Protective Rubber Mat for BRM4 Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 1/8 thick Mat is for placement underneath the Frame of a BRM4 Non-Penetrating mount, on top of Roof surface...

ROHN BRM4PAD Protective Barrier Pad for BRM4 Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/8 thick Pad is for placement underneath the Frame of a BRM4 Non-Penetrating mount, on top of Roof surface...

ROHN BRM6MAT Protective Rubber Mat for BRM6 Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 1/8 thick Mat is for placement underneath the Frame of a BRM6 Non-Penetrating mount, on top of Roof surface...

ROHN BRM6PAD Protective Barrier Pad for BRM6/ 25GBRM Roof Mount
A Protective Layer between the Roof Surface and the Non-Penetrating Roof Mount before Installation. This 3/8 thick Pad is for placement underneath the Frame of a BRM6 Non-Penetrating mount, on top of Roof surface...

ROHN H20 Foot Telescoping TV Antenna Mast

Made in the USA!
ROHN H20, 2 section Mast extends to about 19 Feet in height that ships to Commercial and Residential addresses alike. Used for Off-Air TV Antenna, Amateur (Ham) Radio, Wireless Internet Antenna, MMDS and Cell Phone Signal Booster Installations (not included)...
This Item Ships LTL Freight ONLY...

ROHN H30 Foot Telescoping TV Antenna Mast
Made in the USA!
ROHN H30, 3 section Mast extends to about 27 Feet in height that ships to Commercial and Residential addresses alike. Used for Off-Air TV Antenna, Amateur (Ham) Radio, Wireless Internet Antenna, MMDS and Cell Phone Signal Booster Installations (not included)...
This Item Ships LTL Freight ONLY...

ROHN H40 Foot Telescoping TV Antenna Mast
Made in the USA!
ROHN H40, 4 section Mast extends to about 35 Feet in height that ships to Commercial and Residential addresses alike. Used for Off-Air TV Antenna, Amateur (Ham) Radio, Wireless Internet Antenna, MMDS and Cell Phone Signal Booster Installations (not included)...
This Item Ships LTL Freight ONLY...

ROHN H50 Foot Telescoping TV Antenna Mast
Made in the USA!
ROHN H50, 5 section Mast extends to about 43 Feet in height that ships to Commercial and Residential addresses alike. Used for Off-Air TV Antenna, Amateur (Ham) Radio, Wireless Internet Antenna, MMDS and Cell Phone Signal Booster Installations (not included)...
This Item Ships LTL Freight ONLY...

ROHN ETMB Universal Telescopic Push Up Antenna Mast Roof Mount
Made in the USA!
is designed to facilitate Roof Mounting ROHN H50, H40, H30, H20 and Channel Master 1620, 1630, 1640, 1650, 1820, 1830, 1840, 1850 Telescopic Masts...

ROHN GTMBLTelescoping Antenna Mast Base Plate
Made in the USA!
Telescopic Mast Base Plate is designed to provide base support for ROHN H50, H40, H30 and H20 Telescopic Masts. Use in both Temporary and Permanent mounting. Installation on top of small poured cement footer is ideal...

Rohn 5-16S 5 Foot 16 AWG HDG Swaged Antenna Mast Section
Made in the USA!
This 5 Foot (60") by 1.25" OD 16 AWG swaged end Antenna Mast tube is HDG galvanized for weather and used to extend any 1-1/4 inch 16 gauge antenna masts by fitting the swaged end of this mast into the open end of the other mast tube, thereby extending the existing mast an additional 5 feet. Manufacturers recommend that masts heights of 10 feet and higher be guyed...

Rohn 5-16 5 Foot 16 AWG HDG Antenna Mast Section
Made in the USA!
This 5 Foot (60") by 1.25" OD 16 AWG Antenna Mast tube is HDG galvanized for weather resistent and can be used with a 16 gauge swaged  to extend       extend any 1-1/4 inch 16 gauge antenna masts , thereby extending the existing mast an additional 5 feet. Manufacturers recommend that masts heights of 10 feet and higher be guyed...

Rohn 10-16s 10 HDG Foot Galvanized 
Made in the USA!
This is a 10 Foot (120") by 1.25" OD 16 AWG HDG Galvanized Swaged Antenna Mast (Mount Not Included)...

ROHN DEP30 30 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP40 40 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP50 50 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP60 60 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP70 70 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP80 80 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP90 90 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP100 100 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP110 110 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP120 120 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP130 130 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP140 140 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN DEP150 150 Foot Direct Embed Pole
Minimize site requirements, lowering lease rates and acquisition costs. They are designed for rapid installation, meeting the demands of today’s dynamic communication environments.

ROHN TT050TSP 50 Foot Pole Climbing Safety Cable System
With enough fixtures and climbing cable to install on poles up to 50 foot in height. Does not include Harness or Wire Grab...

ROHN TT100TSP 100 Foot Pole Climbing Safety Cable System
With enough fixtures and climbing cable to install on poles up to 50 foot in height. Does not include Harness or Wire Grab...

ROHN TT150TSP 150 Foot Pole Climbing Safety Cable System
With enough fixtures and climbing cable to install on poles up to 50 foot in height. Does not include Harness or Wire Grab...

ROHN LRCL 5 Foot 5/8" Copper Clad Lightning Rod
5 foot by 5/8 inch copper clad Lightning Rod for Tower installation, threaded with nuts. Installs on most Tower Series Top/Beacon Plates and attachments made for this purpose...

ROHN TT-WG-500 TUF TUG Wire Cable Grab Fall Arrestor System
A Component designed to work within the TUF TUG Safety System. This is a Passive Fall Arrestor Dual Cam Wire Grab that will attach to your Harness and grab the stainless steel strand running length-wise, up and down the Tower that was installed for this purpose...

ROHN TTFBH-2D TUF TUG Journeyman Climbing Harness with 4 "D" Rings
Part of the TUF TUG Safety System, Tower Climbing Harness...

ROHN TTFBH-C/P TUF TUG Professional Climbing Harness with Seat
Part of the TUF TUG Safety System, Tower Climbing Harness...